Pages

Thursday, January 30, 2014

Autodesk Remote..... How it Saved Bacon.... Where Bacon = Time

“Extraordinary creature! So close a friend, and yet so remote.”
 Thomas Mann

My Dad had a saying.... "That really saved our bacon."  I heard him say it countless times. 

Earlier this week, I had reason to heard that quote echo in my ears.

I was faced with a big challenge.  I needed to install Autodesk Vault Professional on a computer in our training room, restore a filestore and database, perform some testing, and upload the data when it was all done.

And while one of the training machines was an ideal place to do this, the problem was that there was a class using that training room for three days!

Three days!  So what to do?  I didn't want to lose three days waiting for the room to free up!  And staying late?!?  No way!

So, I turned to a solution from the Autodesk ExchangeAutodesk Remote.   Important note!  You have to be on subscription to use it!

So what exactly is Autodesk Remote? 

From the Autodesk Exchange Website...

Autodesk® Remote is a stand-alone application for Microsoft Window 7 and 8 and is compatible with all Autodesk products. It lets you drive Autodesk software installed on your primary computer from a remote computer for fast access to native design data over standard networks. To use it, simply install Autodesk Remote on the PC you want to share. Install it again on the machine you want to connect from and start your connection. Note: dual monitor support is the #1 request from early adopters. We’re listening and actively working on it for the next release.


In short, it lets you run one computer from another via your Autodesk ID.   Then you drive one computer, from another.

Remoting to one machine from another
 I can hear everyone now "That's just like (insert name of app)".  And you're probably right.  There are a ton of tools both free, and not free, that will do exactly what Autodesk Remote did. 


And if you're happy with your app... Use it!  I'm not writing this to create a mass exodus from your app off choice.

So why am I writing a post about this one?

Because it filled a niche, when I needed it.  It was the perfect tool at the right time, for exactly the situation I was facing.

So what did Autodesk Remote do that was worthy of heavenly lights and voices singing? 

First, what problems was I facing?

I had to...
  1. install Vault Professional 2014
  2. configure a license file to run Vault Professional 2014
  3. restore a backup to Vault
  4. test data once Vault was configured
  5. upload data to an FTP site once the tests were over
  6. I had to do all of this without being able to access the machine I was using as a server

Autodesk Remote saved me by...
  1. installing quickly.  Class started at 8:30am.  I installed around 8:20am, and was done in less than 5 minutes
  2. Connection was fast. I had no problems connecting.  It took me more time to walk back to my desk than to make the connection
  3. allowing me to completely run steps 2 and 3 from my desk, in another room
  4. because I was able to accomplish tests 2 and 3, steps 4, 5, and 6 were done at least a full day than if I had to touch the computer


So if you do work remotely with computers in your network on a regular basis.  Take a look Autodesk Remote.  The bacon you save might be your own...

Saving time.... saving bacon....

It's also important to note that Autodesk Remote that let you remote to your computer from an iPad as well.  However, I didn't use it with my iPad.  Just my laptop.  

If anyone has use the iPad app, feel free to share a comment!

Friday, January 24, 2014

I Forgot to Add Express Tools to AutoCAD! Now What?

“There is a way in which the collective knowledge of mankind expresses itself, for the finite individual, through mere daily living... a way in which life itself is sheer knowing.”
Anonymous

One thing that can easily happen when installing any version or flavor of AutoCAD is to forget to install the Express Tools.

It's easy to miss them, but if they need to be added after installation, it's not hard at all.

Here's the steps to do it!

The first thing to do, is locate Add/Remove Programs in the Windows Control Panel.   Find AutoCAD, and right click on it.  Choosing Uninstall/Change

I'm using AutoCAD Mechanical 2014.  Keep in mind you may have a different version or flavor of AutoCAD!


Choose "Uninstall/Change" from the control panel

AutoCAD's installer will start.  Choose Add or Remove Features on the first screen that appears.

Choose "Add or Remove Features"

Click through the screens until a list of AutoCAD Features appears.  If Express tools has a red 'X' on it, check the box so it has a green arrow like in the image below.  Once Express Tools is selected, click Update.

Make sure to select Express Tools and choose update.

 AutoCAD will update.  Let it run, finishing when it completes.

Updating the feasture
 Once the update is complete close the installation dialogs and start AutoCAD.

If the Express Tools don't load, there may be one more step that has to be done.

Type CUILOAD at the AutoCAD command line.  Choose browse and locate the file acetmain.cuix.  The default location in Windows 7 is:

 C:\Users\<username
>\AppData\Roaming\Autodesk\AutoCAD Mechanical 2014\R19.1\enu\Support\acetmain.cuix. 

But bear in mind that the location can vary slightly with different versions of AutoCAD, and system configurations.

Click Open to close the first dialog box.


Choose , followed by Close to load the *.cuix file and then close to dismiss it.

Loading and closing the menu





After these steps are done, the Express tab should appear in your AutoCAD installation, and you're ready to go!




Ta Da!  There it is!
And for a video showing the above procedures, take a look below!





****************Edit 31-October-2014 HAPPY HALLOWEEN! ************************

Just yesterday, I used this very technique to add Express Tools to a users machine.  And while all the toolbars were added successfully, I received a "Unknown Command" warning when trying to execute one of the Express Tools functions.

Fortunately a quick Google search found the following result on the Autodesk Website

The steps I used was to type OPTIONS, and on the files tab, choose the Browse button.

 Browse to the path


Navigate to the following directory \Program Files\Autodesk\AutoCAD 20XX\Express, and choose the Add button to add the path to the support directory.

The path added in


Once I had done that, the Express tools were working just fine!


Monday, January 20, 2014

Using Raster Views in an Autodesk Inventor Drawing

“There's no sense in being precise when you don't even know what you're talking about.”
John von Neumann

One of the new functions in Autodesk Inventor 2014 is creating a drawing view as a raster view, and allowing the user to make it precise at the time of their choosing.

For starters, what's the point of starting a view as a raster image, then making it precise later.

Simply put, it lets the user to defer the full calculation of drawing views until later.  Imagine this on a large drawing view with a lot of calculations involved.  Now extend that across multiple projected views.  It can take quite a while!

Placing the views as raster views lets the user quickly place the views initially, then choose which views to make precise when needed.  The "hit" on calculation can be spread out over time.  Make one view precise, and work on it?  Going to a meeting?  Calculate another view while you're gone!  Going to lunch?  Make another view precise, and so on! 

So that's the purpose of it!  Now, how does it work.


When creating a base view on a drawing sheet, there's a check box to Raster Views Only.  With this check box selected, the views will be placed quickly.

Checking the Raster Views Only checkbox

Aside from selecting that check box, placing views is the same.  Once the views are placed, there will be green brackets around the views that are being represented as raster views.

Green brackets indicate these are raster views
At some point, however, it will become necessary to make the views precise.  To do that, right click on the view, and choose Make View Precise.


Calculating the views into precise views.

The green brackets will disappear, and the view is now precise.


One view is precise now.  The others can be calculated later, when needed.
Other views can be made precise later, when they're needed.  The views don't have to be calculated at once!

And for a video description of the steps!  Take a look below! 



And for even more information on this tool, take a look at the Autodesk Online help video at the link here!


Wednesday, January 15, 2014

Controlling Component Participation in an Assembly Level Feature in Autodesk Inventor

As an artist, I've always wanted to participate in the dialogue of art with other artists.
Jeff Koons

I've always considered assembly level features a bit of a specialty tool in Autodesk Inventor.  That doesn't mean I don't think it's a valuable tool.  It just means that it seems like there are users who really use it, and there are users who never touch it, with very little middle ground.

When I'm playing around with wood working projects, I use it a lot.  It's perfect for creating things like dowel holes and hinge slots.  These features are typically creating in components that are already assembled together in wood working.

 Today, I was slowly building a Pie Safe in Inventor from plans I found in a Fine Woodworking article, and the time came to add the hinges to the doors.

A 'Quickndirty' rendering I created in Autodesk Showcase

The hinges need to have clearance cut for them, which is pretty common, even expected.

A typical hinge pocket.
Image courtesy Fine Homebuilding
 Since the door would be assembled by this point in the construction, I reached for my assembly feature, created my sketch, and extruded my cut.

And something happened I had forgotten about.  Inventor cut the slot alright!  But it cut right through the hinge too!  The assembly feature cut everything in it's way!

Doh! That's not what I wanted!

At first glance, one might think that this tool isn't very helpful if it's going to blindly cut everything that gets in it's way.  But Inventor does give us the ability to control what the assembly feature cuts.  All that's needed are a couple of clicks.

The first thing I need to do, is locate the assembly feature in the browser.  Expand it, and a list of the components that are "participating" in the extrusion appear.  In this case, it's the component making up the edge of the door (2013-22-27:3) and the two hinge leaves (Generic Hinge1:1 & Generic Hinge2:1).

Components participating in the feature


 What I really need to do is tell Inventor not to have the hinge leaves participate in the extrusion!

I do that by selecting each hinge leaf, and choosing "Remove Participant". 

Removing the participants


Once the hinge leaves are removed from the feature.  Everything looks as it should!  My design intent is truly captured!



So that's how to tell Inventor not to include components in an assembly level cut.  If you're using this tool, I think this could be an important aspect that could get easily overlooked. 

And as one last tip, what if a component needs to be added to the assembly level feature, that is told that it needs to participate?

If that's the case, right click on the feature, choose "Add Participant" and select the components you wish to add.  Give it a try!

Participants can also be added to an assembly level feature

And for a video on the steps I showed above, take a look below!



And one final note, more information on the assembly level feature can be found in the Inventor help system here!

Monday, January 13, 2014

A Review - A Look at Infinite Skills "Learning Autodesk Inventor 2014"


Back near the end of 2013, I was asked to review Learning Autodesk Inventor 2014 video based training created by Infinite Skills.  So I took some time, dove deep.  I wanted to not just take an overview.  I wanted to dig into it and really understand it.

Before starting anything, I think it's important I say that I didn't get compensated in any way for this.  I was just given a link to download the files, and then the freedom to take a look at the files.  Beyond being supplied training files, I was free to formulate my own opinions.

With that out of the way, I'd like to start out with how I see video training.  Personally, I'm a big fan of video based training. I've created several videos myself, and I use them whenever possible. 

However, having instructed several courses myself, I've always thought that they couldn't replace class based training.  I've just thought it's too hard to replace the interaction, and experience of live instructor.  I guess you can say I'm a little biased that way.

But it's time to set my biases aside and take a good look.

What I liked!

The first thing I did, was take some time to get used to navigating the viewer.  I found that it's easy to get used to and simple to use.  There was also a pretty good help system if I had a question on the navigation. 

The videos are organized into fairly short segments, most of them a few minutes long.  I thought this made it easy to take them in small increments and avoid getting overwhelmed.

And example of the videos organized
 Plunging into the videos, starting with Inventor's interface, I found the instructor, Adam Cooper, to be easy to listen to.  He wasn't monotone, but he wasn't "over the top" trying to be entertaining.  He was the right amount of giving the information in a engaging, and interesting way.

An example of the lessons on screen.

I also noticed that he pointed out things that he did out of his preference.  Not because it was a "better" way to use Inventor.  Just that he liked a setting, or this approach, and why he does it.  It shows his experience, and an understanding that there are many approaches that work, and each user can choose which they like at their discretion.

 I also quickly noticed was the depth of information that was included in the videos.   Far more information that I felt I could give in a lecture.  That level of information would be too overwhelming in a lecture format. 

An example of depth of information.  Talking about Application Options

The nature of having the lessons in a video format, with the ability to bookmark them, made for a much easier mechanism to take in the information being provided.

Which brings me to what I found to be another useful feature.  The bookmarks.  At any point a video can be bookmarked so it can be returned to at a later time.  So if a subject of particular interest is found, it can be bookmarked, complete with a title and description, for later reference. 

The bookmark page.  VERY useful!


What I didn't like so much

While my overall impressions were very good, nothing is perfect.  And while I won't say there's something "bad", there are some things that I wish were better.

To begin, as much as I liked the amount of information being, I think there's a chance the information could become "drinking from a fire hydrant" for the new user.  I would certainly recommend reviewing the videos and using the bookmarks to their full advantage

And this one is a pet peeve of mine, pure and simple.  Every once in a while, the key strokes came through on the video.  While the information is all good, and it in no way impacts the quality of the information, I would have been a happier not hearing them.  Granted, I was using a headset with the videos, which makes the keystrokes more prominent.  Yes.  It's a minor thing. But as I said, a peeve of mine.

My conclusion?

I like the Infinite Skills Inventor 2014 videos.  I think they're an excellent learning resource for someone looking for some self paced learning, at home, or on the job.  The videos are well structured and have all the information needed to provide someone a solid foundation using Autodesk Inventor.

The amount of information provided is very thorough.  I like that.  I like the ability to see the different settings and approaches for tools in Inventor.  Being someone who likes to see the options and choose one I like the best, I like the depth of information that was provided. 

At the price point of $99.95 USD, the investment isn't going to "break the bank", especially when compared to the time lost and frustration of the "hunting and pecking" method of learning software. Money spent on good training will save time when the software is used "in the wild".

My ultimate conclusion?  I think this is an outstanding learning resource!



Wednesday, January 08, 2014

Making the Right Selection - Selection Tricks in Autodesk Showcase

Design is not making beauty, beauty emerges from selection, affinities, integration, love.
Louis Kahn

Once again Marion Landry has come through with a great post on selecting objects in Autodesk Showcase. 

While selecting objects in Showcase isn't a difficult task, there are always tricks that will make it even easier.

Check out some of Marion's tricks that make selecting objects Showcase a snap!


Friday, January 03, 2014

WHAT DID I JUST DELETE?!? - Recovering a Deleted File from Dropbox

I am prepared for the worst, but hope for the best.
Benjamin Disraeli

Over a year ago, I created a "poor man's" Autodesk Vault backup scheme using my Dropbox account. 

In short, my Vault Data is backed up to a folder that syncs to my Dropbox account, creating a simple cloud backup. 

Information on how I did that are found in my post here.
 
I've been using it for a year, and it's worked great.  I've never had a problem with it.

That is until now....

First, this wasn't a problem with the scripts, my internet connection, or Dropbox. 

Each one of these tools worked flawlessly. 

It was the user (that's me!) who screwed this up!


So what did the user do? 

I had to restore a different Vault Database and Filestore for a customer test.  I ran the backup, which actually failed because I didn't have enough disk space. 

But that, is a separate issue.

The rub? I neglected to make sure I had a safe backup of my own Vault data in a safe place. 

So what happened?

My scripts ran just like they were set to.  They removed the data from my dropbox folder, in order to make it ready to be replaced by a new backup....

Which was never made due to the failed backup of customer data...

And my cloud Vault backup was destroyed.

Had I really just effectively killed all my personal Vault data? 

Thankfully, no.  Lucky for me, Dropbox has a way to restore lost data.

First, browse to the folder where the data was, and choose "Show Deleted Files"


A list of the deleted files will be displayed.  Now right click on the files to be restored, and choose "Restore"!


Now the files are resurrected, and all is good again! 

Needless to say, that backup is now residing in a safe, safe place!  

For the full instructions on recovering a file deleted from Dropbox, check out their help at the link HERE!  There's more than one way to do it!