Pages

Friday, January 27, 2017

Making up Miles by Measuring Inches - My 3DConnexion CADMouse Anecdote

***Disclaimer!***
The pictures I'm using for this blog post are of my home laptop running Autodesk Fusion 360 with a CADMouse and SpaceMouse, both made by 3DConnexion.  Security at work limits what I images I can share from my work station.

Better safe that jobless!

*** End Disclaimer!***


It's likely we've all heard the quote "A journey of a thousand miles begins with a single step".  And I'm just as sure that millions of "bar-stool philosophers" like myself have used it in some sort of discussion or debate.

Earlier this week, the microcosm of my CAD station gave me a moment to reflect on that quote again.

Since I started at my new position as a mechanical designer about a year ago, I've had a 3DConnexion SpaceMouse Pro and 3DConnexion CADMouse.  What can I say, work takes good care of me!

My laptop running Fusion 360.  I need to program buttons for this too. 
At one point, I had all the buttons mapped, and I was happily using radial menus and hotkeys.

But then, our CAD stations were upgraded, and all my settings were lost.

For most of that time, I keep telling myself.  "I need to rethink what commands I use most frequently, and start programming them into my devices."

And for most of that time, I've told myself.  "I really need to finalize what commands are really important to me.", or "I'll do it tomorrow.", or the infamous, "Once things slow down a bit."

That's how nearly a year passed with all my buttons set to their default settings.

My CADMouse menu in Fusion 360


Finally, I told myself, "Jon, just pick a command and program it!"

So I did.  I picked a few commands, and put them into my SpaceMouse Pro and CADMouse.

Programming the menus for my 3DConnexion CADMouse
And nearly instantly, I started wondering why I hadn't done it sooner!

What were the lessons I learned? 

  • Don't fall victim to "Analysis Paralysis".  I postponed making a decision until I had all the information.  The problem is, I had no hard stop to when I was done evaluating.  I could always "test a little longer". 
  • Just start already!  It's not like the path can't be changed while keeping the destination the same.  
  • We get so focused on the big goals, we forget the little steps.  Nobody knows that I customized my SpaceMouse Pro and CADMouse.  And there's really no need for them to.  But navigating my CAD system is much easier because I took a few minutes to do so.   


Conclusion?

Now, it's not like my 40 hour week suddenly turned into a 30 hour week, or that project that's going to take 18 months suddenly took twelve months because of my pre-programmed 3DConnexion devices.

But what did happen?

Things were just smoother, and dare I say a little more pleasant.  I wasn't reaching for my keyboard for commonly used hot keys, moving across a large monitor to get to an icon.

Now it didn't take my 40 hour week and make it into a 30 hour week, but it did make navigating my tools a little easier.

It's like having your favorite stations preprogrammed into your car radio.  It doesn't make a dramatic change in the lenght of your commute, but it does make the time you spend more pleasant.

Sometimes, it really is about the journey! 






Monday, January 23, 2017

Fusion 360 - 5 Updates on January 19th, 2017

Just a quick post on Fusion 360.  

Late last week, Fusion 360 received an update!

I won't spell it out here. Autodesk has already done that in their post explaining the update here.

Take a look at the new features and give them a try. 

Myself, I'm interested in the new branching preview they've added! 

Branching has been added! You can see it in the upper left corner of the screen.
I know I'm looking forward to some more features in the future!

Sunday, January 22, 2017

Back in the Learning Saddle Again - In Classroom and Life!

A little update on the going on with me, and Inventor Tales as a blog.  

I'm back in class four days a week along with my day job as a Mechanical Designer, so things have gotten rather busy again.  

Which I'm afraid does rob time from my working with Fusion 360.

This time I'm studying DC electrical theory.  That means a lot of time in lecture and lab, right now I'm learning how to simplify series-parallel circuits. 



Then it means a couple of hours in the lab wiring circuits to make sure the concepts have really set in. 

The first, and simplest circuit I wired.  

That does mean slowing down my posts on my CAD products, yet again.  As my time is limited.  But I do plan on doing my best to share what I learn when I do have the time.

But one thing I can share, is a quick lesson I learned earlier this week.  One where my aircraft maintenance classes helped me in my "day job' as a mechanical designer.

It was during a discussion about how flared fittings are attached to a semi-rigid line.  

An example of a flared semi-rigid line I made in class.
The discussion related to the process of how it would be accomplish, as well as a few pros and cons as they applied to an aerospace valve.

And because of my aircraft maintenance classes, I've actually flared a 37 degree line myself. 

The tube in the flaring block.
Because I had taken these classes, I was better equipped to be an asset for my job.  

What's the lesson here?  Not all of you work with aviation applications, so a 37 degree flare may not apply to you.  

But the lesson I think you can take away is to keep your desire to learn alive.  And find something, whatever it is, that both interests you, and keeps you learning!

And I'll see about picking back up on those Fusion 360 posts soon!

And one last thing!

Here's a little video on the process of flaring a tube for an aircraft application!

Sunday, January 15, 2017

A360 to Share a Fusion 360 Model - I Got the Feedback I Needed In Minutes!

There are many examples of people who have used computer aided design programs like Fusion 360 to create models for replacement parts that can no longer be located.

It's a fantastic technology, one that in my personal opinion is still in it's early stages.

This is my experience with a knob on the stove in our home. Now, this isn't a story of how I created a model, had it 3D printed, and how incredible the end product is.

There are many of those stories.  And their success is well deserved. 

I'm just sharing a step in the journey as I learn about the process first hand.  I may follow through and find success!  Or I may find, for some reason, it's not worth pursuing any further. 

But carrying that dose of reality. Here is the first step in that journey, building and sharing the model. 

Building the Model - The Easy Part! 

Building the model was a process of measuring the knob.  That meant pulling out my trusty set of calipers and carefully measuring the knob.  I had to make sure that the dimensions, particularly where it mounted to the stove were correct.  



The process of modeling took only about two relaxed hours on Friday morning, which for me is a day off. That part was pretty easy. 

The stove knob modeled in Fusion 360.
But now I've finished my model and it's only about 9AM.  I'd like to share the model with her, but she's just started her day at work.  

So how do I share the model? 

How do I share the model quickly, easily, and effectively so I can get feedback as soon as possible?

My Answer - A360

In a previous post, I mentioned that Autodesk 360, or A360, mirrors your Fusion 360 projects.  Now was time to take advantage of that for collaboration to a fuller, if not completely full form. 

I opened the model in A360 and opened the file in the A360 viewer.  I clicked the share icon to start the sharing process. 

The knob in A360.  Notice the "Share" icon in the upper right.
After selecting "Share" the sharing options will show up.  


In my case, I made sure the file was shared.  Then I copied the link to my instant messaging program, and sent it to my girlfriend.

After a about 30 minutes, she had taken a look at the model in her internet browser, and had given me a few thoughts on what I had done.

First circle completed!

Thoughts on Collaboration

While very tech savvy, my girlfriend isn't a CAD operator.  But with just a link, she was able to view the model in all it's 3D glory.  I didn't have to take half a dozen screen grabs, and wait for an email.  Points to A360 for that.  The online view did all it needed to do, and it did it quickly, and efficiently. 

My total turnaround time was less than 3 hours from starting to build the model, to having my girlfriend's feedback. 

On another note...  If your aware of Autodesk's Live Review you might be wondering why I didn't use it. The answer for that is a simple matter of logistics.  With my girlfriend at work, I had to accommodate her schedule, which meant sending her a link that she could use at her convenience.  Sending a link was the best tool for this task. 

Next Steps?

The next thing to do is look into getting the part 3D printed.  The main question is will it be cost efficient.  There's no sense if the cost to make a new knob is 20% of the cost of a new stove.  

But that's what I'm trying to learn by going through this process.  

I'll keep you posted on this part of my journey!  You're learning along with me!   Or at least that's my hope! 

And if' you'd like to look at the Fusion 360 model yourself.  Here's a link!  Feel free to have a look.




Friday, January 06, 2017

Autodesk A360 and Your Own Private Wiki

One thing I've learned from my aircraft maintenance classes, as well as from my various aviation mentors, is that the information surrounding a design can be every bit as critical as the design itself.

For example, aircraft have extensive logbooks recording all maintenance and inspections that have been performed on the aircraft.  At any time, your friends from the Federal Aviation Administration (FAA), can drop in and say.

"We're from the FAA, we're here to help.  May we see your aircraft maintenance logbook?"

A typical aircraft maintenance logbook.  This is not to be lost! 

Needless to say, if you don't have an accurate and updated logbook, you may feel a few beads of sweat on your forehead.

The point of my little anecdote is that when working with an aircraft, product, or design, the information that drove your design in a given direction can be every bit as important as the design itself.

That information may come in the form of spec sheets, vendor quotes, or meeting notes.

What would you do if you were asked, "What information drove you to make the decision you did?

In my experience, these documents are often misplaced or even worse, lost forever.  Meeting notes get thrown out, spec sheets get dropped in "a network drive somewhere", and vendor quotes are left in "an email from a few months ago".  

As I've taken a deeper dive into Fusion 360 and Autodesk A360, I've found that A360 provides a nice tool that can help with that very thing.

A360 has a "Wiki" folder that let's you create documents letting you keep the information you need with your project.

The "Wiki" folder hidden in A360.

It's a special folder where you can add information and add links to whatever information you deem important to your project.

Here you can create multiple documents, share them with other members of your team, and allow them to comment, and update the documents.

A sample of my A3t60 Wiki.  I only have one page started


In my initial test, I created a Wiki page with links to important documents that I might need.  These references are documents from the FAA, links to important technical documents, and helpful instructional videos.

The Wiki page I created for my Fusion 360 project.

Now is that all you can do?  Hardly!  Personally, I've only just waded into the shallow end of the pool.

But it's something I intend to make further use of, and if you're using Fusion 360, I think that it's worth taking a look at what this Wiki folder in A360 can do for you.

After all, if you don't record it, it's like it never happened in the first place.

So what do you think you could use this Wiki page for?

Share your thoughts!  In the spirit of collaboration, let's all learn together!


Wednesday, January 04, 2017

Fusion 360 and A360 - Using Them Together

There's a lot of talk about Fusion 360 and all the things it can do, and there should be! It's a great tool that does a lot of great things, and it's doing more all the time.

But just as important, is sharing the right information, and sharing it with the right people. 

If you've used Fusion 360 before, you've almost certainly used the data panel.  It's where your projects and project data is stored and organized

The data panel, ever present, on the left of your screen


But did you also know that it's folders are mirrored to Autodesk cloud storage service A360

The folders mirrored in A360
If you're a big Fusion 360 user, you may be shrugging and saying, "so what?"

But what if you need to share that data?  What if you need to access that data from multiple computers or mobile devices?  

A360 can come in handy for that, sharing with consumers who may not be Fusion 360 users.

Maybe they just need images for marketing, or maybe it's something that you or your team want to review on site?

Maybe you just want to embed some code to create a view-able file for a blog post... (spoiler alert!)


That's a job for A360!  

So before you throw it in the "Wastebasket of Meh", give it a thought or two, and think about how you can use it. 

I know it's possibilities are inspiring me, and I'm looking forward to exploring further! 

Since I can access my data on my tablet, exploring should be easy! 

Can you hear the music to "Travelin' Man"? 
I'm looking forward to sharing what I learn! 

I'm already getting some great ideas! 



Monday, January 02, 2017

The First Post of 2017 - Fusion 360... And Now What?

Here I am, sitting on my couch on New Years weekend.  I have one more day off of work, and another week before aircraft maintenance classes start again.

I've had a little bit of time with Fusion 360.  I've been playing around, just making a few parts and renderings.  And most of all, continuing to explore it's possibilities.

An elevator bearing bracket.  Modeled and rendered in Fusion 360. 
There's still much more for me to look into, and as Fusion 360 is updated, more features appear all the time (and that's a good thing!).

But now that 2017 is here, what is the biggest thing to I'm looking forward to?

Flat out accessing data anywhere I want.  I don't have to worry about where I saved data, was it put in a PDM system like Autodesk Vault, and can I access it where I currently am.

As long as it's saved in Fusion 360, and I have a connection to the internet, I can see the data.

I've already been able to access data on my tablet on a site. Far more portable than having to open up a laptop and boot up!

Tablet and Laptop.  Syncing data with no extra effort on my part! 


And I'm looking forward to taking a bigger advantage of that!  I'm also looking forward to sharing more!

So here we go, 2017.  Time to pave a new trail and see what the future brings us!