Find us on Google+ Inventor Tales

Friday, October 26, 2012

All for Fun – Creating a 20 Sided Die

Death and the dice level all distinctions.
Samuel Foote

Many years ago, I friend asked me to create multi-sided die for a website he was creating.  You can still see the images on the banner of the website for DiceHouse Games here.

It was a tricky one to create.  It was a 20 sided die, a much used tool in role playing games like Dungeons and Dragons.

An Autodesk Showcase Rendering of the 20 sided die model

I also used it as an example in a blog post for using the “Change View Orientation”  tool inside of Autodesk Inventor drawings back in February 2012.  

***Edit 13-Nov-2012 : Added an embedded dwf of the 20 sided die***


A 3D dwf of the 20 sided die

*** End Edit***
Since that time I’ve started getting requests for how I built the die, as well as a location to download the actual *.ipt file.  

So here are the steps on how I built the 20 sided die!  


1. I found the definition of a Icosahedron (a 20 sided polygon) on Wikipedia.


The construction figure that started it all!

2. I created three sketches on the XY, YZ, and XZ origin planes in Inventor


The three rectangles on each plane to create the framework

 
3. Next, I used a 3D sketch to connect the vertices together, must like in the Wikipedia image.  If you’re wondering, this did take quite a bit of time. 


The process of creating the skeleton



4. This becomes the skeleton where I create several boundary patches.  The boundary patches create the surfaces of the die using the “sketch skeleton”.    This was also pretty laborious!

Boundary patches created close surface that could be stitched.


5. I then stitched the surface.  Since it’s “watertight” (completely sealed), it becomes a solid.

Stitching the surfaces make it a solid
6. Now it I had to add all the numbers (which were extrusions), and fillet the sharp corners. That’s it, I was done!


The completed die

So in conclusion, this was a satisfying little project took a little bit of research to figure out how to construct it.  Once I figured out the process, the steps weren’t difficult, but it did take time and patience to execute. 
 
Placing the 3D wires lines took a lot of time, and more than once I had to correct a line I misplaced.  The boundary patches took less time, but putting in all the numbers was an exercise in patience too.
 

So because of the requests, I’m uploading the file to a couple of sites for download.  However, before you go grabbing the file, I make only one request.
 

I spent several hours of a Saturday figuring this out.  All I ask is if you use this model, give me a nod and a little credit for the time I put into it.  
 

Now for the download sites!
 

The first is my Autodesk 360 site: Click here for Autodesk 360 download
 

If you use the GrabCAD file sharing website, you can also log in and get it here:  Click here for GrabCAD download


Sunday, October 21, 2012

Using the Transitional Constraint in Autodesk Inventor

Life is pleasant. Death is peaceful. It's the transition that's troublesome.
Isaac Asimov

This week proves to be another busy week as my second round presenting at the Autodesk Manufacturing Academy (this time in Cerritos, Ca.) comes around. 

That's right, even though I've been through it one time, I have to review my sessions, polish, an improve them.  Not to mention making sure I don't forget anything! 

But I did find time to create a quick video on an Autodesk Inventor tool that has been around forever, but seems to have drifted into obscurity as new features and functions have appeared over years of Inventor's evolution.

That tool is the Transition constraint.

The Transition constraint being applied to a "Cam and Follower"

Looking at the image above, it might make sense to use the Tangent constraint.  It would seem perfect to hole the cam and follower together. 

However, if this constraint is used, the tangency will only follow one face.  It won't transition to another face like the follower would in the real world.

This is where the appropriately named Transition constraint comes into play.  It can "see" the faces it need to transition to, and behave appropriately.

By using the Transition constraint.  Inventor will allow the follow to "follow" the cam correctly. 

Below is a video showing the behavior with the Tangent constraint, which isn't what I want, then I'll show the behavior with the Transition constraint, where we get to give the "big ol' nod of approval"! 

Thursday, October 18, 2012

A "Guest VIdeo" on Autodesk Showcase Materials

“The only thing more expensive than education is ignorance.”
Benjamin Franklin

Every once in a while I run across a resource that really captures my interest. 

Sometimes it's some sort of low pass by an airplane with a big piston engine, other times it's something silly like the "fainting goat" video YouTube.

But yesterday I came upon two fantastic Autodesk Showcase videos created by Marion Landry from Autodesk.

Marion created two outstanding videos on creating and manipulating materials in Autodesk Showcase.

I've already watched them once, and I picked up quite a few tricks I'll use in the future.  As a matter of fact, I'll watch them again, just because I know there are more tricks I'm going to pick up.

So here are the videos that Marion has graciously created for us.  Be sure to check out her channel here!

Creating Custom Materials Part 1



Creating Custom Materials Part 2


Sunday, October 14, 2012

A "Weekend Sebatical" Learning Practical Sheet Metal

“So never lose an opportunity of urging a practical beginning, however small, for it is wonderful how often in such matters the mustard-seed germinates and roots itself.”
Florence Nightingale

This week, a video blog post gets postponed.  Why?  I took a "weekend sabbatical" and took a two day class on hand building sheet metal aircraft parts. 

Why?  Because I miss getting my hands dirty, I love learning new things, and I wanted some practical knowledge that is only learned on the bench with real

I've seen the volunteer mechanics at Planes of Fame Air Museum working their craft, and been amazed by how easy the make it look.  All the while knowing it's not nearly that easy. 

So there I was, standing over a bench, looking at a pile of unformed aluminum parts,  countersinks, riveting guns, and pneumatic drill motors, wondering how I was going to "use those to turn that into something that looked like a simple aircraft structure".


My completed "practice project" is at the top.  I'm supposed to turn the pile of metal into something resembling a wing structure!
 I look around a second, and wonder if this is a good idea after all.  If I run now, no one will ever know.  I think for a second.

The first day I spent on a "practice part".  Just getting the hang of center-punching, drilling countersinking, and riveting.

This was my "practice" project.  All I did here was get used to the tools. It's partially completed here.

The first real life lesson I learned.  There's skill that goes into this.

Not that I thought it was a simple task before I tried it.  I knew it took skill, but it takes a lot of skill. All those mechanics I saw who made it look easy, are more than mechanics or technicians.  They're masters of their craft.

So how did that practice project go?
  • I got my holes drilled more or less in a straight line.  (Even center-punched, the drill walked a bit),
  • The countersinks came out good (redemption!)
  • The rivets were more or less correct.  (I need to be more diligent about preparation)
I did learn that it's no big deal to center-punch and drill out a rivet though! 

The next day, I had to actually make a basic wing box.  I learned how to use a wooden form the ribs from flat sheet.

Then it was more drilling, deburring, countersinking, and riveting.

Beginning the wing box.  Cleco pins temporarily hold it together
 And when I say a lot, I mean a lot!

I bucked flat rivets, universal (domed) rivets, I pulled pop rivets.

I drilled, bucked and drilled some more.

The partially assembly wing box with the top skin being attached.
 I learned a lot about how things like this are done.  I learned even more about how not to do it!

So in taking the time to do this project what did I learn that I can apply back to my "Computer Aided Design World"?

  • For every step I thought I knew about the process, there's some someone who has been around for twenty-some-odd years who knows all the steps I never heard of.
  • The term "sweat equity" is something executives use to describe hard work.  It's equivalent on the shop floor is "blood, sweat, and tears".  Building something with my own hands made me appreciate the value of the latter term.  The latter term is far more literal.
  • Speaking of  blood.  When a craftsman of this trade cuts himself, he'll clean the part before getting a Band-Aid, because he knows "blood is corrosive". 
  • Yes, I cut myself on the edge of an aluminum panel.  This doesn't really hurt, but bleeds quiet a bit. 
  • I also pinched my finger in a Cleco clamp.  This bleeds a lot less than the cut.  But hurts orders of magnitudes more. 
Note:  Close one of these on your finger, and it will hurt... a lot!
So in summary, it was a great experience for me.  If anything, I now know what it takes, and what I'd have to learn to be half the craftsman that those mechanics are.

This weekend gave me a new perspective on what it takes to build those designs that come so easily in the computer, and that it would be wise for me to never take that craftsman level of skill for granted.

So I guess the final question?  Will I continue, after spending an entire weekend building something that was mediocre at best and busting my knuckles (literally), would I take something like this on again?

Absolutely.  And why would I tackle this again?

Because however many mistakes I made, and however ugly that first part came out. 

I know I can do better, and I know I can learn more.  

And I learned to appreciate the craftsman that make it look so easy.


The completed project.  This is the "good" side.  Don't even look at the other!






Thursday, October 11, 2012

Outside the Box with Autodesk Inventor Publisher and Techsmith Camtasia Studio

“Hindsight explains the injury that foresight would have prevented”
~Unknown

For the second time, I've taken a video exported from Autodesk Inventor Publisher, and created a set of narrative instructions by editing the video in Camtasia Studio by Techsmith.

In this case, I created it as a sample for KETIV's Autodesk Manufacturing Academy in Oregon, which was yesterday, October 10th, 2012,  and California, coming up on October 25th, 2012.

Just like before, I started with an assembly.  This was a Dual Throttle Assembly provided by Datum3 Studios

The Dual Throttle Assembly created by Datum3

But just like any "2.0" version, this one is improved.  Sure, I had better tools in the sense that I had more current versions of both softwares (Inventor Publisher 2013 & Camtasia Studio 8.0), but I also have gotten better at creating them as well.
 
But putting aside the "fun and excitement" portion of the task, I realized there was a "real world" lesson hidden in my fun and games.

First, think outside the box.  I know I can be guilty of thinking about using my set of CAD tools to solve all my engineering and design problems.  Sometimes I fail to ;ook beyond what I can do with a little bit of creativity.

In this example, I wanted to use a voice-over.  Perhaps text or video instructions alone just won't cut it.  Perhaps this is going to be a file for use overseas.  With the help of a translator, a voice over could be created in several different languages for several different locales.


Not to mention the fact that I got to edit the video exported out of Inventor Publisher, edit it, and throw some cool transitions and effects.

That's where I took the video file from Inventor Publisher, imported it into Camtasia Studio, and started the editing process.  I threw in transitions, intro and outro slides, as well as watermarks, and credits!  

And as part of that "credit where credit is due" process, I can't thank Datum3 Studios for the use of their Dual Throttle Assembly..  This project would have been a lot tougher without their help!

Check the Dual Throttle assembly, and some of their other cool work, on their projects gallery here! 

So here's the result of a some spit and polish, and a few virtual blood, sweat, and tears.  I hope you enjoy, and maybe get a little inspired by a project I had a lot of fun creating.




AMA Oregon was great, by the way.  I only had time to take a few pictures off my smart phone, but here's a little of what went on!

KETIV's John Aiello presents to the crowd

Janna Spicer explains the benefits of the First Robotics Program

And everyone had a chance to mingle!





Sunday, October 07, 2012

Crunch Time Previews! - Linking between Autodesk Inventor and Autodesk Showcase

“My body felt extremely tired, ... I've got five or six gears in me, but I was crunching to get into second without a clutch. It was a tough day.”
Grant Hackett

Today is a much shorter post that usual, since most of my waking hours has been spent on creating my materials for KETIV's Autodesk Manufacturing Academy in Oregon on October 10th. 

So in this post, I'm afraid I don't have much that I can get into regarding new adventures or experiences, since..... well.  Look at that above statement on AMA!

But to that end, I've got a fantastic dataset graciously provided by Datum3 Studios.  You can check it out as the "Flight Controller Bases" section in the gallery HERE!  This data will be playing a big part in my "Digital User Manuals & Documentation" session.

The Throttle rendered in Autodesk Showcase
As part of the event, I've been busy creating supplemental videos that go along with the sessions, so this is what I'm sharing today.

In this video for AMA, I briefly show how Autodesk Inventor and Autodesk Showcase can link their data together, creating a loop of "collaborative development" where the rendering in Showcase can develop along side the engineering design developing in Inventor.

By utilizing this process, the aesthetics of a product can be developed and approved by the customer, all the while the engineering is going on in the background.  Both can develop simultaneously, instead of linearly as in the "traditional way".

Here's the video!  I hope you all enjoy this AMA preview!



Sunday, September 30, 2012

Using Model Sketches on a Drawing in Autodesk Inventor

“You can't do sketches enough. Sketch everything and keep your curiosity fresh.”
John Singer Sargent

Last week, I was talking to someone about how to best represent a spot weld in Autodesk Inventor.

The first observation to make is that Inventor has a Weldment environment that provides several tools to help with welding.  It's got a variety of tools.  It can separate the weldment into different sections, the assembled environment, the preparation environment, the welded environment, and finally machined environment.

This is a great tool if a high degree of detail is needed in creating a welded environment.

But what if  just a simple representation is needed?

In the brainstorming session, an idea was brought up.

What about creating a sketch in the assembly, showing the spot welds in the sketch, then showing it on the drawing?

The sketch added to the model

The sketch added to the drawing


I tried it.  It works!  The sketch can be shown, annotations can be added and so on. 

Here are the basic steps:
  1. Create a sketch on the model (part or assembly)
  2. Place the view in a drawing.
  3. Right Click the Assembly in the Drawing Browser
  4. Choose "Get Model Sketches"

And BOOM!  That's it.  It's pretty easy!

So keep this in mind for your designs.  And keep it in mind for any application it can help in.  I used spot welds in this example, but any place a sketch can help, use it! 

Of course, here's a video showing the example I described!


One last thing.  Do you have a place where this workflow helped you out?  Share a comment and let me know!

Sunday, September 23, 2012

An Autodesk Manufacturing Academy Preview video - iParts

“The whole is more than the sum of its parts.”
Aristotle

It's been another busy weekend.  I was busy catching up with family, so I'm afraid no blog was built today. 

However, I have been busy putting a lot of work into KETIV's Autodesk Manufacturing Academy, so as this weeks post, I offer up a preview video for my "Automating Repetitive Designs" session.

This particular video is on the iPart portion of the session

Recall that an iPart is a "table driven part" where a component of shape can be controlled, via parameters.  This makes it much easier to create different sizes, colors, and so on, without recreating the part every time.  The table helps drive that geometry.

A classic example of an iPart, open up the McMaster Carr catalog, and look at any screw you can find.  See that table of values?  iPart!  

So without further delay, here's a video.  Enjoy!

I hope you enjoy, and I hope to see a few of you a the AMA event!

I'll see you in next week's post! 




Friday, September 21, 2012

Off Topic - The Space Shuttle Endeavour

“What is history? An echo of the past in the future; a reflex from the future on the past”
Victor Hugo

It can definitely be said that this post is off topic.  I didn't use Autodesk Inventor, Autodesk Showcase, or anything for this blog.

All I had was the opportunity to see the Space Shuttle Endeavour make her last flight to her final home, The California Science Center.

I couldn't resist.  This would be the last time that I could see a space shuttle in the air, even if it was riding piggy back on a Boeing 747.

A few of us from the office headed a few miles down the road to Anaheim, and saw the 747 carrying Endeavour on it's fly by of Disneyland.

It was impressive on so many levels.  The engineering feat of the 747 carrying Endeavour, the excitement being able to watch history being written. 

And last but not least, a little bit of sadness knowing that this is the end of an era.

So hear are my pictures of "Endeavour's Last Ride".  I hope you enjoy them as much as I did! 

At first it looked like a ghost in the Southern California haze.
But it was very real indeed!

You could feel the excitement in the air.

It was amazing to see it get closer.

And just keep getting bigger.

And bigger!

And become a truly impressive sight!

The chase planes look tiny!

A grand entrance for Endeavour

And she heads away

Her flyby is over.

And a grand space craft heads for her final home.






Wednesday, September 19, 2012

Backing Up Autodesk Vault - On a Budget

“Back up my hard drive? How do I put it in reverse?”

I would be the first to say that we should all be making backups of our CAD data!

Do you think I follow my own advice?

Pffft!  No! 

Of course I have my excuses!
  1. My CAD Data isn't use for production, so it's not critical.
  2. I work in a highly mobile environment, and everything runs on my laptop.   That means I 'm not connected to a good backup server much of the time
  3. I'm too lazy to take 15 minutes to plug in my portable hard drive and copy my Vault Backup over to the drive. 
  4. The most famous, used by many; (wait for it). "It hasn't failed yet!"
Are these good excuses? 

Pffft! No!  

So if  the The Oatmeal's Famous "Tumbeasts" made an appearance and at my hard drive, I was out of luck.




Try passing this excuse off at work.


One day, I had an epiphany that was worthy of MacGyver.

I implemented it, and thus far it's been working well! 

First I had to take stock of my assets.
  • I already have a script that backs up my Autodesk Vault database and filestore that contains my CAD data. 
  • I have a Dropbox account that has more than enough room to accommodate my current backup
  • At my home, I have an old retired computer that I use as a data server, which also has plenty of room for my Vault database and filestore.
That's enough for me!

I created a new script that moves my backup file to a Dropbox folder.  In turn, that folder syncs up with my online Dropbox account, which is stored in the cloud.

My Vault Backup in my Dropbox Folder


BOOM!  Backup! 

Then, I setup my old data server to sync with my Dropbox account, so now I have a backup at home, as well as on online! 

BOOM!  Redundancy!  

I've been running this system for about a week now, and it's been working pretty well.  I've restored from it once already successfully

But just like everything it's got good and bad. 

First the good!
  • It's a simple and effective backup strategy, especially for the budget minded. 
  • By using Dropbox, I can sync the backup to multiple machines, they just have to be syncing to the Dropbox account.
Now the not so good!
  • Since this is a cloud backup, there needs to be sufficient bandwidth to support uploading and downloading potentially gigabytes of data.
  • Online storage accounts, such as Dropbox, Autodesk 360, and SkyDrive have limited storage capacity (typically a few gigabytes until you purchase more).  So monitoring usage can be important, especially as data gets larger.
Fortunately, my Vault data is about 750MB, so I have more than enough room in my Dropbox account (over 6GB), and I upload across a fiber optic line, so bandwidth isn't an issue for me, so this is effective for me.

In summary, this system probably isn't good for everybody, but for a small environment, with limited resources to purchase hardware and infrastructure, it may be exactly the ticket.

P.S.  I'm sure there are those of you might be wondering why I didn't use my Autodesk 360 account.  The reasons are simple.  I tried my Dropbox account first, and I'm too busy (read too lazy) to switch it over.  I could just as easily have used my Autodesk 360 account!

I hope this is a tip you might be able to use in your own environment!

Have another idea to create a backup like this on a budget, check out the comment section! 

Sunday, September 16, 2012

Using an iFeature in Autodesk Inventor - Part 3


“All respect comes from persisting to completion.”
Melissa Lima

At long last!  The final part of my little "iFeatures & Autodesk Inventor" series (at least for now)!

In this final post, I'll discuss taking and iFeature, and driving it via a table.

But first of all, why drive an iFeature with a table?  What does a table do for us?

Well the single biggest reason to use a table driven iFeature is to create is to create a consistent series of choices for features that vary in predictable ways.

An Example of an iFeature Table
For example, lets say there's a mounting hole of three consistent variations.  It may have two different size holes, but the holes all expand in intervals of a given increment (.125 inches for example).

An example of different holes (yes, I know the biggest one is 'too big'
If  a non-table driven iFeature is used, the different diameter holes could be mixed and matched.

The 'standard' iFeature screen
In other words, a "create a combo" situation could arise, and a non-existant hole created.

If a table driven iFeature is used, then the mounting holes can be called out by a specific value, such as an "tool number", and a consistent set of holes can be placed.

Special fields can also be created, so institution specific criteria can be used for selecting an iFeature.  For example, in my video, I use Tool Number.

But enough of the describing! Let's switch to the video, and see how these tables can be used!


And on a final note.... Who knows what an iFeature was called before it was named an iFeature? Hint: it's the reason an iFeature has the file extention "*.ide"!

Monday, September 10, 2012

A KETIV AMA Preview Video - Automating Repetitive Design Tasks

“All the people were nice. They all acted like family and friends.”
James Bush

During this weekend, there was no time to create a video for the blog I was hoping to create. 

It was lost for one of the best reasons a weekend could be lost.  I had friends come from out of town for a visit! 

So this weekend was a blog free weekend (and even a mostly computer free weekend) that was consumed by catching up with life long friends, so part three of my iFeatures blog post will be delayed a bit.

But all is not lost.  Here's a preview of the video series that will accompany the Automate Repetitive Design Tasks session at  Autodesk Manufacturing Academy  on October 10th in Lake Oswego in Oregon, and October 25th in Cerritos, California.  

I hope to see you there!  


And here's the preview for the whole event!  Check it out!


Sunday, September 02, 2012

Using an iFeature in Autodesk Inventor - Part 2

“Ideas are the building blocks of ideas.”
Jason Zebehazy

In my last blog post on iFeatures (see that post here), I extracted and placed an iFeature, but that was all we did at that time.  I did mention that dimensions could be added to the iFeature, but I stated we'd get back to that.

Well, we're back to it!  In this blog (and its video), we'll add dimensions to the iFeature we used in the last blog.

The basic steps for this process are below:

  • Rename Parameters (okay, this isn't strictly necessary, but it makes the process easier, and I recommend it. 

Parameters renamed
HINT!  To rename parameters quickly, edit the feature, and type "Parameter_Name = X.XXX" to rename it in the feature.  This will rename the parameter directly from the feature it drives.

Renaming the parameter in the feature

  • Extract the iFeatures you want.  Note in the image below, the renamed features automatically are made available to the iFeature.

Extracting the iFeature


  • Set any ranges or lists you need


Setting a range
Setting a list
  • Save the iFeature, and you're ready to go! 

Saving the feature

  • Now the feature can be placed, taking advantage of the settings used!
Placing the iFeature.  Notice the list being used.

So that will place the iFeature into the parts you intend to use it in, and now you've seen the steps to create this iFeature.

But it would be an Inventor Tales blog without a video.  So here it is, a video showing the process! 


Have a suggestion on how you might use iFeatures?  Throw a comment!

Friday, August 31, 2012

Blurred Reflections in Autodesk Showcase (via Autodesk)

“Sometimes in our confusion, we see not the world as it is, but the world though eyes blurred by the mind.”
Unknown

As we head into a long weekend here in the states.  I found a cool video produced Marion Laundry at Autodesk. 

Why do I like this video so much?  Marion showed a great tip that I hadn't taken advantage of yet! (Hint: Never stop learning!)

How to blur reflections!  I've always thought that if a rendering looks "too perfect", it gives it away as being a computer generated image.

It's a fact of life, nothing is perfect.

Take a look at this Lockheed P-38 Lightning owned by Allied Fighters in California.  It's got a pretty shiny paint job.  Not fully polished, but pretty shiny.

The Allied Fighters P-38 Lightning "Honey Bunny"
 
Notice how the reflections are blurred however?  It's not a mirror finish. 

Marion's Video gives a great tip on how to create blurred reflections.  So instead of talking about it, check out the video below! 

One last note!  While it should be obvious right away, I DID NOT CREATE THIS VIDEO!  This is created by Marion Landry at Autodesk, and all credit belongs to her!  Take a look at her channel here and check out more of her videos!



And just for the fun of it, here's a video of Honey Bunny in flight at the Living History Event at Planes of Fame Air Museum.  With a unique camera perspective too!


Wednesday, August 29, 2012

Autodesk Inventor's Special Functions in Parameters

“Nearly all men can stand adversity, but if you want to test a man's character, give him power.”
Abraham Lincoln

Today, just a little tip for a midweek blog!

Most of us are familiar with Autodesk Inventor's Parameters.  It's where Inventor stores the dimensions that it uses to create it's components.

If you've used parameters before, you might even know that you can rename the parameters to give it more meaningful names than the defaults.

The Parameters used for this part


An additional capability of the parameters is the ability to build equations using Inventor's parameters.  Many of us have seen those before too.



Equations in Parameters can help make a design much more intelligent

But what many may not know, is that there are many special fuctions that can be used.  For example, the "Ceiling" function can round a number up to the nearest integer, while the "Floor" function will round a value down to the nearest integer.


For example, in the equation below : Maj_Dia_Ht / 0.4375 = 4.571 without an additional function.

Using the Ceiling function to round up to then next integer

But add the "Ceiling" function: Maj_Dia_Ht / 0.4375 in = 5.0 because this function rounds up to the nearest integer.

Why did I use this function?  Because I'm calculating the number of holes in the circular pattern, and this number needs to be an integer (you can't have 4.571 holes in a pattern!).

This is just a quick example of what can be done, but there are several functions available/

For more information on these functions, check out the Autodesk Wikipedia site

Take advantage of these when building equations!  Use the to your advantage!

Sunday, August 26, 2012

Using an iFeature in Autodesk Inventor - Part 1

“Ideas are the building blocks of ideas.”
Jason Zebehazy

The Autodesk Inventor iFeature.  I've described it as Inventor's version of an AutoCAD Block.  When there's a repetitive feature that needs to be placed multiple times with repeatability, this is a place to look.

First, Autodesk Inventor has several iFeatures that ship with it.

Inventor ships with several iFeatures built in
You can find them by clicking on the "Insert iFeature" icon.  It's found on the Manage Tab.

Placing iFeatures
But the iFeatures Inventor has may not cover all the iFeatures that might be needed.  In that case, new iFeatures can be created and added to the library.

In my humble opinion, I think this is one of Inventor's tools that gets overlooked.  While it may be an answer for every solution, there are definitely some places it can make a job go by a lot more easily. 

 The iFeature has a lot of flexibility, among these are:

  • The ability to add variable dimensions that can be changed by the user
  • The ability to limit these dimensions to a list of numbers, or a range of numbers
  • The ability to create table of variants for different types of placed features

So there is a quite a bit to go over.  So I'm going to break this particular blog into parts.  So in the first part, I'll just show how we can create an iFeature, and place it onto a part.

A couple of suggestions before the video, I like to create an "iFeature generator".  That is, I create a component to build the iFeature.

I do this because if I need to adjust the iFeature, I can return to the generator and make the adjustments I need. 





My iFeature Generator for this post

Trust me, I learned this one the hard way.  In this case the hard way wanted to make an adjustment to my iFeature, but having to rebuild it because I didn't save it the first time!

So to see how this iFeature was used, take a look at the video!


And if you're looking for some additional iFeatures to use, try Charlie Bliss's site here!

Friday, August 24, 2012

Autodesk University 2012 - It's Coming and the Class Schedule is Out!

“I'm not the smartest fellow in the world, but I can sure pick smart colleagues.”
Franklin D. Roosevelt

Autodesk University 2012.  It's coming around again starting November 25th (click here for full Schedule) in Las Vegas, Nevada!

AU Image Courtesy of the Autodesk University Website.

For those who aren't aware of Autodesk University (commonly known as AU), it's a series of classes, seminars, and network sessions on all manner of Autodesk Technology.  I've gone in the past, and I think it's well worth attending.

But as they say, "don't take it from me".  Take a look at the class schedule HERE!  Take a look at the classes that are available this year.

And on a final note, become an AU Member and become eligible for early registration!

Tuesday, August 21, 2012

KETIV's Autodesk Manufacturing Academy- We're Baaaack!

“He's a good guy to pick his brain a little bit. It's great to be by his side and talk to him and learn from him and watch his work habits.”
Sean Marshall

It's back everyone!  KETIV's Autodesk Manufacturing Academy returns to Lake Oswego in Oregon (October 10th), & Cerritos in California (October 25th)! Registration is now open!

I'll be there again, and so will all the techies from the KETIV team!

So if you need a reason for work to send you to Oregon, or Southern California, check out this link

(nudge nudge) Check out the keynote speakers!

And look below for the "preview movie".  If you look quickly, you can see me.  It's like Where's Waldo for bald guys!

Monday, August 20, 2012

A Weekend Off & Updates for Autodesk Showcase 2013

“Celebrate the happiness that friends are always giving, make every day a holiday and celebrate just living!”
Amanda Bradley

I was out of town this weekend, enjoying a short weekend excursion to Big Bear, Ca. with some friends.

It was a good weekend of hanging out, having a drink or two, and enjoying attending the local Renaissance Faire.

So this week, there isn't an Inventor or Showcase Video.  But since last week I posted about the release of Autodesk Inventor Update 2, I thought I'd continue the theme of updates and point out that Autodesk Showcase 2013 has updates for it as well.

So if you're running Autodesk Showcase 2013, and you want to make sure you have the latest updates, check the following links:

Update 1 for Autodesk Showcase 2013

Update 2 for Autodesk Showcase 2013

Note that Update 2 does include Update 1.  So if you want to jump straight to Update 2, you can install that without having to install Update 1 first.

I'm hoping to get a video out later this week, but until then, here's some pictures of the Faire I attended!

Adam the "Bawdy Juggler" - Quite a show!

"Gallows Humor" A band that put on a great show!
And a video showing some of the jousting.  These guys weren't acting!  They knocked the snot out of each other.