Find us on Google+ Inventor Tales

Monday, December 31, 2012

Happy 2013! Taking a weekend off!

Happy new years from Inventor Tales!  I'm taking the weekend off this time, but Inventor Tales will be back with new posts for 2013!

I'll see you all in 2013! 

Thursday, December 27, 2012

Splitting Tables in Autodesk Inventor

“Let the gentle bush dig its root deep and spread upward to split the boulder.”
Carl Sandburg


As I'm waiting for 2013 to arrive, I came across a little tip in Autodesk Inventor that it could be said falls into the "I never noticed that" section. 

Splitting a hole table.

Once upon a time, when I was designing stamping dies, there were many a time that the hole table describing all the holes in a die plate would run off the page. 

Back at that time, I was using AutoCAD, so breaking was a matter of inserting and manually populating blocks.  

But what happens if the same thing needs to be done with Inventor?  Below is an example of a hole table I want to split.  I know the table isn't that long, and probably doesn't need to be split in this case, but bear with me, it's just an example!  Besides, I didn't feel like modeling a part that did run off the page!


A table in need of splitting

Let's say I want to split the table at the row 'C1'.  All I have to do is right click inside one of the fields, and choose "Table>Split Table".





Splitting the table.  Make sure to click inside one of the fields
After choosing the "Split Table" option, the table will split at that cell.  Click and drag on the tables to reposition them.  The hole table can then be split again, and again, as needed!

Repositioning the newly split table.

That's all there is to it!  But there's a couple of other tips worth knowing. 

1) If the table needs to be "recombined", right click on the table, and choose Table>Un-Split Table

Combining a "un-splitting" a split table.

 
2) This is very important!  Don't click on the border of the cell! The "Split Table" option will gray out if the border of the cell is clicked on!



This is what happens when clicking on the border of a cell!
So that is today's short little tip.  A few tricks that I hope are helpful. 

Have a few thoughts you want to share?  Feel free to drop a comment or two!

Wednesday, December 26, 2012

A Holiday with Autodesk Force Effect Motion

"Never mistake motion for action.”
Ernest Hemingway

As the holidays approached, I found myself finally taking a look at something I had told myself to look at, and "never got around to it". 

It was Autodesk's Force Effect Motion.

If you're not familiar with Force Effect Motion, it's a mobile app that works on Apple and Android devices, and allows for the laying out of mechanical mechanisms on a mobile device, instead of using paper and pencil, or even firing up a CAD package like Autodesk Inventor or AutoCAD.

A Force Effect Motion diagram - Courtesy of the Autodesk Force Effect Facebook Page.
 
So to satisfy my geeky curiosity, I imported two images to try out as backgrounds.  The first was a picture of the landing gear for a Douglas DC-3, the second, the extended and retracted positions for a Boeing B-17 Flying Fortress

I had a lot of fun playing with these two mechanisms.  It allowed me to sit on my couch, and analyze the landing gear mechanisms and better understand how they worked!

I can see how using this application can help get a mechanism conceptualized before firing up a CAD application and creating models that may have to be thrown away because part way through the process, it's realized that I've gone down the wrong design road. 

It's like creating a napkin sketch, but with the added benefits of being able to modify the diagram, and avoid getting food on your engineering designs! 

In conclusion, I have to say I wish I had tried this app out sooner, but now that I have, I'm glad I did.  The next time I'm at Planes of Fame, I'll definitely be getting  a few more pictures of landing gear mechanisms to try out! 



So here are a few videos.  First, a video from the AutodeskMFG YouTube channel, showing how to use Force Effect Motion.
\

And next, the videos I created, showing the DC-3 and B-17 landing gear mechanisms.  \





Monday, December 24, 2012

Happy Holidays from Inventor Tales.

“A good holiday is one spent among people whose notions of time are vaguer than yours.”
John B. Priestly


It's Christmas Eve today, so I'm taking a break from a post this week.

This weekend has been a wonderful snowboarding holiday with friends in Mammoth, followed by Christmas with the family. 




A gorgeous view off of Chair 5 at Mammoth

So it's time for a few days off of tech stuff. 

Happy Holidays to everyone out there!  Enjoy your Holiday!

~Jon Landeros

Sunday, December 16, 2012

Matching Colors in Autodesk Showcase

“Don't miss all the beautiful colors of the rainbow looking for that pot of gold.”
Unknown

If you want to know how important getting the proper color of a logo can be.  Get it wrong and see how quickly the Marketing Department comes looking for you.

The truth is it can be very important.  For things such as color schemes and logos, it can be critical.  Company "red" is not just "red".  It's a specific red, or blue, or yellow.

The KETIV logo.  It's not just "red".  It's got a specific RGB value.

When working in Autodesk Showcase, there have been a few times where I've needed to use a specific color.  And if it really is that important, I'll ask for the RGB (Red, Green, Blue) values of the color.

Many times, the Marketing Department has those values, and can provide them for you. 

But I recently I ran into a case where I needed to match the color of a logo as closely as possible, and and I didn't have the RGB values to work with.  So what did I do?

I could have played with the color until I matched it by eye, but that can be time consuming to do, and I wanted to get as close as I could, as quickly as I could.

Fortunately, when editing a color, showcase has an "eye dropper" icon that lets you select and existing object, and "paint" it with that color.



Edit the color by right clicking on it, and choose the eyedropper
I was able to use it to select the object I needed to match the logo with the eyedropper, and "paint" the object with that color.  It worked like  a charm! 

Of course this isn't as accurate as having the RGB values.  But when I couldn't get the RGB values, this was more than adequate to get me what I needed!  It also saved me a huge amount of time because now I didn't have to finesse the color into play.

So for that, Here's a quick video on how I used this nice little trick




Tuesday, December 11, 2012

A Couple of Success (and Hopefully Inspirational) Videos

“Have great hopes and dare to go all out for them. Have great dreams and dare to live them. Have tremendous expectations and believe in them.”
Norman Vincent Peale

Technology marches a long at a staggering pace.  As a matter of fact, I'm not even sure it's marching.  It's sprinting like a jackrabbit hopped up on Red Bull.  

Is it stressful?  Sure!  Trying to keep up with all this change isn't easy. 

Is it difficult?  It can be.  Knowing what to implement is as tricky as knowing what's available to you!

But is it amazing to see how technology is changing things?  Yes it is!  It's exciting to see the evolution, and even revolution, in technology.

To that end, I'm sharing a some videos that I hope offer some inspiration.

The first is from the General Session at Autodesk University 2012, where the CEO of Autodesk, Carl Bass talks about "What if?"  and how technology, particularly Autodesk technology, is fueling the answers to that question. (Thank you CADRelations for the video)



And to show a company that came up with creative answers to "What if?"  Here's a story on GK Machine is using Autodesk products to improve their products and processes.



But how about this story of using technology to answer the "What if?" question, as cool as it would be to say it is.  The video and story are worth checking out.  It's about a group of five high school kids built a flight simulator for a Colonial Viper from Battlestar Galactica!  Autodesk Inventor played it's part as the tool that enabled it, but imagine where these kids are going with technology!

First.  Here's the Gizmodo story on how they got started! 

 But they followed through with it, and got it done!

Here's the completed nearly product and accompanying story from Gizmodo!

***Edit 11-Dec-2011***

I found the link to the "The Viper" Webpage!.  Check out their team site here!

***End edit****

How cool is that!

Sunday, December 09, 2012

A Quick Tip on Positioning Section Lines in Autodesk Inventor

“I went to a bookstore and asked the saleswoman, "Where's the self-help section?" She said if she told me, it would defeat the purpose”
George Carlin

Creating section views with Autodesk Inventor.  It's not a difficult thing.  But there is a trick I sometimes use that I think is worth sharing on how to position the section line. 

The most common way, is to choose one of the projected construction elements.  This will grab things like the center or quadrant of a circle, a midpoint of a line, or a vertex where two lines meet.  This probably covers nearly all cases of what most users need to do.

The construction element

But what if there's a case where a section line needs to be placed a certain distance from the edge, and no convenient point exists?

First, place a section line on the view, but don't let it constrain to anything.  I like to place the section line completely off the view geometry to make good and sure I don't pick a point by mistake.



Placing the section line "off the geometry".


Now with the view placed (it looks like a projected view right now), right click on the section line, and choose "Edit".

'
The section view completed off the geometry

Now to edit the placed view

Now the sketch the section line lives on becomes active, and it can be positioned using constraints and dimensions, just like any sketch.  One important thing to note.  Make sure to use the "Project Geometry" tool to project geometry off the view.  Otherwise it can't be picked.

Use project, constrain, and dimension to position the section line.


Once the geometry is projected, it can be constrained and dimensioned like any sketch!

The completed section view

Do you have  a place this might be helpful!  Drop a comment!

And naturally, here is the accompanying video!

Friday, December 07, 2012

Autodesk Vault 2013 and Microsoft .Net 4.5 - Not Cool Together


“Never, never, never, never, never! Pray you, undo this button.”
William Shakespeare

Earlier this week, after attending Autodesk University 2012, I decided to install Visual Studio Express, so I could go ahead and try my hand at the Autodesk Inventor API.

The download went fine, and soon I was installing away.

As the progress bar cruised along, I noticed one message, "Installing Microsoft .NET Framework 4.5".

I wonder if that's a good idea?  I thought.  But I dismissed it.  I was going to lunch, and my mind was elsewhere. Like food.

When I returned to the office.  Visual Studio was merrily installed.  All was good in the Kingdom of Laptop.

I wasn't going to be able to work with Visual Studio, so I moved on and worked on other projects.

Eventually, that other project led me to look for some files out of my installation of Autodesk Vault 2013. 


These are my files, as last left.
I open up the folder where I know the files are, and......... Nothing.  No files appear.  NOTHING! 

Imagine the camera panning away from me as I scream: "NOOOOOOO!"

Now all I see is this!

 I have that sinking feeling.  Did the files get deleted?  This my personal Vault.  Nobody else accesses it.  And I didn't delete them.

On a hunch, I change from Detail to Icon view.   My files appear!  They're still there!
 



But why won't they show in the Detail View?

Suddenly I remember.  .NET Framework 4.5.....  The tingle in the back of my neck was trying to tell me something.  I remember it's not a good idea to install it with Vault!
 
All is NOT well in the Kingdom of Laptop.

 Fortunately, I had a restore point and was able to "hit the eject button" and return to a state before Visual Studio.

Needless to say, if you're running Autodesk Vault 2013.  Stay away from .Microsoft .NET 4.5.

I don't know that .NET 4.5 is bad.  As a matter of fact I doubt it.  All I know is that it doesn't play well with Autodesk Vault 2013.  I wouldn't expect it's going to play well with earlier versions either.

So until Vault supports .NET 4.5, stay safe, stay away.  

Don't do what I did!

****EDIT 2-August-2013 ****

I'm a bit late in updating this, I'm afraid it slipped by me.  But Service Pack 1 for Autodesk Vault 2013 addes support for .Net 4.5!  So if you're seeing this issue, make sure Service Pack 1 is installed.

It a can be downloaded at the link here!

Tuesday, December 04, 2012

Wrapping up a Little Fun - Modeling the Six Sided Die

"It means that I, like God, do not play with dice and do not believe in coincidence."
"V" From V for Vendetta

Afrer modeling nearly all of the gaming dice, (20 sided, 12 sided, 10 sided, 8 sided, and 4 sided), I decided to complete the set with the 6 sided.

Originally, I was going to post this particular die as a bit of a joke.  Draw a square, extrude it into a cube, break the edges and slap some numbers on it.  How hard could it be?

Examples of 6 sided die (courtesy Wikipedia)

Could you believe I found a way to complicate it?  And find a use for a new trick in the process?

I'll share the trick at the end of the blog.  First, I'll start out with the steps I used.  Which let's face it, aren't that difficult.  But there might still be a trick or two to use.

1) First, I created the cube.  Since I used Autodesk Inventor 2013, I used the "Box" primitive that was added in this release.

Using the "Box" primitive to create the cube for the die.


2) Next, I added fillets to break the sharp edges.  I used the "All Rounds" option to get every edge.

Adding fillets to break the edges


3) Finally, I added the numbers to each side of the die.

Finally, adding the numbers!


And that's it.  The die is finished.

But there's an epilogue to this exercise.  Looking at the die, I didn't like the way it looked. The edges were too crisp and clean.  It didn't look like a real die would.  I decided I wanted the vertices of the die to look more rounded than the rest of the die.

Looking carefully the rounded corners can be seen (image courtesy Wikpedia)

Thg "too crisp" corner shown.  I'm using the "shaded with edges" setting to show the corner more clearly.

So how did I go about changing that?  I edited the fillet, created in step 2, and on the "setbacks" tab, I chose each corner of the die, and changed the setback until I liked the result (I used .1875 in my case). 

I found it gave a much more eye pleasing result than the tight corners I initially had.



Changing the setback
The completed die with setback
Ironically, I can't think of another time I've really used the setback setting.  It's possible that I might have used it somehwhere, but I can't recall one. 

I guess it just goes to show that one should never say "I'll never use that tool!"

And naturally, I have to add a rendering from Autodesk Showcase, just because!

And one for the show!


And if you want do download the model here you go!

Click here to download from Autodesk 360 (no login required)

Click here to download from GrabCAD (login required)

I hope you find this model an interesting diversion! 

Sunday, December 02, 2012

Creating Arcs without Exiting the Line Tool in Autodesk Inventor

“Force never moves in a straight line, but always in a curve vast as the universe, and therefore eventually returns whence it issued forth, but upon a higher arc, for the universe has progressed since it started.”
Proverb

Autodesk University 2012 is over!  And frankly, it was fantastic!  I had a great time, met some wonderful people, and learned a ton of new things!

But a consequence of getting all that information is.... I'm beat!  So as I play catchup on sleep, and life, this blog post remains quite brief.

Has anyone out in the verse, while sketching, tried to create an arc from a line in Autodesk Inventor?  It can be done by using the "arc" tool, but it's going to likely remain returning to the sketch, and adding sketch constraints.

This tip comes from the "bucket of little things" that are simple, but make sketching easier.  This is how to create a tangent, or perpendicular arc without exiting the line tool.

1) Start drawing the lines required for the sketch

Start with the line tool.

2) Stay in the line tool when ready to create the arc.

Don't exit, stay in the line tool!



3) Click on the start of the arc, and while holding the left mouse button down (this is important!), imaging drawing the arc with a pencil.  Make sure to hold the left mouse button down until ready to create the arc.

Getting ready to create the arc


4) Draw the arc (either perpendicular or tangent) while holding the left mouse button down.  When ready, lift the left mouse button.  Now you have created an arc!

When ready to create the arc, lift the left mouse button.


Granted, there is a trick to it, and it takes practice.  The single biggest tip I can offer is to draw a little more slowly, and definitely more deliberately!  Rushing the task usually means making mistakes and redoing things.

But with a little practice, I think this is a great tool.  I encourage giving it a try!

For a little added info, here's a video to go with it.



Do you have a few thoughts or suggestions?  Add a comment below!

Thursday, November 29, 2012

Just Cool Tech - A Quick Post from Autodesk University 2012

Any sufficiently advanced technology is indistinguishable from magic.
Arthur C. Clarke

Autodesk University 2012 has been just great.  I've learned a ton of new things, and met a ton of great people.  It's been a pleasure to meet so many people that I've only known online until this week! 

A sea of AU attendees.  Dedicated, interested, at energetic AU attendees!


It's also meant running around fueled on adrenaline and coffee, so it's been hard to have a few minutes to write up a blog post. 

But I can at least leave everyone with a couple of images and  videos, and show what I great event it's been!

The Rally Fighter.  Just a way cool car developed by a small company in only months!


Technology at its finest.  The Embrace Nest helping save a premature baby's life

A description of the Embrace Nest

And also video on the ShopBot CNC Router, which has models that cost less than 10,000 USD!  Sure, it's not cheap, but for technology that was tens of thousands of dollars before, this is pretty amazing!



Also, MakerBot has a 3D printer that can be obtained for 2200 USD!  And while for the "Average Joe" that's not small change.  This technology at one time was hundreds of thousands of dollars.  It's amazing how technology like this is becoming more mainstream, and more obtainable.


I need to start saving my nickles and dimes!  

 


Monday, November 26, 2012

Arriving at Autodesk University 2012 Autodesk University 2012

Anyone who stops learning is old, whether at twenty or eighty. Anyone who keeps learning stays young. The greatest thing in life is to keep your mind young.
Henry Ford

Today I'm reporting in from Autodesk University 2012!   I haven't been here since 2008, and now that I'm here.  Just feeling the energy of the place has made me realize how much I've missed it!


Welcome to AU2012

It's going to be a great time of learning, networking, more learning, and seeing some very cool technology.

 An amazing wine rack in Mandalay Bay.  That's technology, right!
'I'm sure I'm going to be going like crazy as I try to assimilate all the cool things that I'm seeing, but I'm hoping to share it all here as the days tick by

Heck of a view from my room!

There's not much to report yet, but that's only because things haven't gotten started.  But soon, I'll be in the thick of it. 

I can't wait! 






Saturday, November 24, 2012

All for Fun! Now, the 4 Sided Gaming Die

God may not play dice with the universe, but something strange is going on with the prime numbers.
Paul Erdos

With this description of how I built the four sided gaming die, my series is nearly coming to a close. 

The completed four sided die.  The yellow "spines" are the work axes used for the circular number to complete the numbers

 This is a recreation of a die I created for a friend who was making a website for Dice House Games in Fullerton.  Ironically, they're right next door to the KETIV office!

I had to recreate the die because I lost the model in between laptops, but I think this is a better design that the original.  So here it is for everyone!

This particular die was pretty simple.  The construction was nearly the same as creating half of the eight sided die.  Although there were some variations with the numbers and basic construction.

The first step, was to create a triangle on an origin work plane.  This becomes one base of the die.

Starting the 4 sided die

\Next came a challenge.  I needed to create a point on the midpoint bisector of the triangle.  For this, I had to reach back into the high school geometry I swore I'd never use!  In truth, I only needed two lines, but the third helped me make sure that everything was right!

Bisecting the triangle

With this construction complete, I could now place a point on the intersection of the lines, and a line through that point, and perpendicular to the plane of the triangle.

I next made sure to make the hypotenuse of the imaginary triangle made by the line the same length as the side of the first triangle I sketched (a screen capture probably makes more sense here). 

Creating the line perpendicular to the first sketch.
Now I lofted from the triangle, to the point I created.  That's it, now I have a four sided die!

Creating the loft that creates the die.
 And next I break the sharp edges with a fillet.

Breaking the sharp edges
 And now the numbers!  In this case, the numbers were actually a little easier.  Instead of creating each number one at a time, the shape and design of the four sided die allowed me to use a work axis and utilize the "circular pattern" tool to finish out each number.  This way, I only had to position each number once.  The circular pattern took care of the rest!




Using a circular pattern makes it easy to create the numbers!


And viola!  The four sided die!


And I'm done!

Of course it wouldn't be finished without a rendering in Autodesk Showcase.


An now a  little rendering!

If you'd like, you can download the file from the pages below!

Click here to download from GrabCAD (login required)

Click here to download from Autodesk 360  (No login required)

Have any questions on a particular step?  Throw out a comment! 

Also, I'll be at Autodesk University 2012 this year in Las Vegas, so you may see my bald head roaming around!   

I'm also planning on blogging from there, so look for some (hopefully) interesting stuff!


Wednesday, November 21, 2012

Accent Lights - An Autodesk Showcase Guest Video

“He has suffused the entire design with a light and transparency that is truly extraordinary.”
Charles Pierce

I know I've been featuring a lot of videos on Autodesk Showcase from Marion Landry's YouTube Channel, but the fact is she's keeps putting out fantastic material.

In this video Marion has created, she provides us with some great tips on using accent lighting in Autodesk Showcase.

I learned quite a few tricks by watching what she's done, and I'll definitely review this video later, as well as keep a close eye on her channel!.

Here's the video below on this tip!



And for those out there that are heading to Autodesk University next week, I'll see you there!  I'm getting all my things in order to arrive Monday.  If you're going, I'll see you there!

Sunday, November 18, 2012

Creating a Breakout View in Autodesk Inventor

“A dream is your creative vision for your life in the future. You must break out of your current comfort zone and become comfortable with the unfamiliar and the unknown.”
Denis Waitley

When I training Autodesk Inventor, I always take a little bit of extra time on the break out view in drawings.  It's a great way of showing details for internal parts inside an assembly, and not difficult to create in Inventor.

A break out view shown created

 But when creating a break out view, it's got one place that usually snags everyone as the first few times they use it.  I know it got me when I first started it.

 That step is, associating the sketch to the view.  If the sketch isn't associated to the view, the break out view won't work, and the breakout command will error out.

This is the error seen when the sketch isn't associated
So how is the sketch associated?  What is it that's so special?

I'll talk about all the steps, and specify that special step to create the sketch association.

1. Click on the view that the breakout view will be placed on. The border will highlight, indicating it's selection.  This is the critical step that will create the associated sketch!

Make sure to select the view before creating the sketch!


2. Now, click the "Create Sketch" icon.  The sketch is created, and it's axes will center on the view.  It's this centering of the axes that tells us the sketch has associated to the view.

Creating the sketch

The centered axes tell us it's working
3.  Now sketch a closed figure around the area to break out. It can be any shape, it just has to be closed.  Here I use a spline. Finish the sketch when done.

Sketch the break out view boundary


4. Now click on the "Break Out" icon.   Select the sketch with the view.

The break out icon

5. Define the options for the break out.  One helpful tip is to point out that projected views can be used to help with the definition, not just the view that will host the breakout.  In the image below, I've used a projected view to define the break out depth.

Setting the options for break out


6. Choose okay and the breakout view is created.

The break out view created

 I could say "That's All Folks", but instead, here's a couple of other tips that I find helpful.

There will be times that not every component in the break out view is supposed to be sectioned, as step 6 shows above.  Here's how to change that.

The first is to locate the part in the feature browser, right click on it, locate "Section Participation", and changed it's setting to "None".

Setting the section options from the browser

The other is to hold down the "Shift" key with nothing selected, and right click.  Choose "Part Priority" from the menu.

Setting part priority


Now select the part on screen, right click, and the same options for "Section Participation" are available.

Setting the section participation from the right click menu


Which ever means you prefer, the sectioning for selected components can be turned off, if desired.

A completed section, with specific parts unsectioned

On a last tip, I've shown what happens when the selections are correct, but how can you tell when the view isn't associated, so a mistake can be quickly corrected before the error on view creation appears? 

There are two quick ways to tell.

1. If the sketch is created, but the axes aren't centered on the view, the sketch isn't associated.

2. If the "Project Geometry" icon is grayed out, then the sketch isn't associated.  This is because Inventor doesn't see any geometry to project.  If the sketch is associated it will.

Two ways to tell if the sketch isn't associated
 In conclusion, I hope this helps a few of you out in the "Verse" with break out view.  It's a great tool, and can be a great way to add informative detail on a drawing.

For a little extra info, here is the video!





<